Principle of As-300 Hall Flowmeter

-

   Principle of As-300 Hall Flowmeter



  • Hall Flow Rate of 50 g metal powders
AS-300 Hall Flowmeter Funnel determines flow rate by measuring the time taken by 50 gram of a metal powder to flow through a calibrated hall flowmeter funnel/orifice of standardized dimensions(0.1 inch/2.5 mm) according to International Standards.



  • Apparent Density of free-flowing powders
AS-300 Hall Flowmeter determines the apparent density by permitting a volume or certain quantity of powder in a loose condition to flow from a hall flowmeter funnel orifice Diameter 0.1 inch/2.5 mm into a specified density cup of definite volume(25 cm³) under controlled conditions. 
The mass of powder per unit volume (the ratio between the mass and the volume) is recorded and reported as apparent density.



  • Apparent Density of non-free-flowing powders
AS-300 Hall Flowmeter determines the apparent density by permitting a volume or certain quantity of powder in a loose condition to flow from a Carney funnel diameter 0.2 inch/5.0 mm into a specified density cup of definite volume(25 cm³) under controlled conditions. 
The mass of powder per unit volume (the ratio between the mass and the volume) is recorded and reported as apparent density.





Related :-
materials,physical metallurgy, information, materials science,science, mining metallurgy engineering, materials engineering, physical, facebook, journal, mining, metals, chemical, metal, ferrous, category, technology, understand, showing, britannica,lowmeter,
rockwin flowmeter india pvt ltd,
electromagnetic flowmeter,
ultrasonic flowmeter,
rockwin flowmeter,
vortex flowmeter,
magnetic flowmeter,
turbine flowmeter,
flowmeter types,
mass flowmeter,
oxygen flowmeter,
coriolis mass flowmeter, 
huygens principle, principle of management ,aufbau principle. 

Comments

Post a Comment

Popular posts from this blog

Atomization process and their types

-
Image
                                                      Atomization Atomization. Atomization, also called the spraying method, is a process in which molten metals are broken into small drops of liquid by high-speed fluids (gas as air or inert gas; liquid as water) or fluids with centrifugal force, and then solidified into powder. There are types of Atomization process are: 1.1 Water Atomization In the commercial production of metal powders water atomization is the pre-eminent mode; attendant capacity worldwide is at least 700000 tyr−1 with production rates up to 500 kg min−1. Water atomization is used primarily for ferrous compositions but can be used to produce a range of nonferrous alloys. It is lower in cost than other modes of atomization but limitations exist in relation to powder purity, particularly with reactive metals and alloys. Nozzles used in water atomization are either in the form of discrete multiple nozzles or an annular slit concentric with the metal stream.
Read more

Machining process information

-
                                                         Machining Introduction :- machining is the most important of the manufacturing processes. Machining can be defined as the process of removing material from a workpiece in the form of chips. The term metal cutting is used when the material is metallic. Most machining has very low set-up cost compared to forming, molding, and casting processes. However, machining is much more expensive for high volumes. Machining is necessary where tight tolerances on dimensions and finishes are required.                  Different Types of Machining Operations :- Three primary machining processes — turning, drilling, and milling — are used as a means of removal. Each process plays a key role in how a product is manufactured and enhances each product’s unique properties... 1) Turning process :-Turning is a machining process performed by a device called a lathe; the lathe spins the given product as the blades cut and scrape away the desired a
Read more

Milling process information

-
Milling Introduction :-Milling is a process performed with a machine in which the cutters rotate to remove the material from the work piece present in the direction of the angle with the tool axis. With the help of the milling machines one can perform many operations and functions starting from small objects to large ones.                         Milling machining is one of the very common manufacturing processes used in machinery shops and industries to manufacture high precision products and parts in different shapes and sizes. types of milling machines 1) Vertical Milling Machines :- The vertical mill has a vertically arranged spindle axis and rotate by staying at the same axis. The spindle can also be extended and performing functions such as drilling and cutting. Vertical mill has got two further categories as well: turret mill and bed mill.                         The turret mill has got a table that moves perpendicularly and parallel to the spindle axis in order to cut th
Read more