Principle of As-300 Hall Flowmeter

-
    Principle of As-300 Hall Flowmeter Hall Flow Rate of 50 g metal powders AS-300 Hall Flowmeter Funnel determines flow rate by measuring the time taken by 50 gram of a metal powder to flow through a calibrated hall flowmeter funnel/orifice of standardized dimensions(0.1 inch/2.5 mm) according to International Standards. Apparent Density of free-flowing powders AS-300 Hall Flowmeter determines the apparent density by permitting a volume or certain quantity of powder in a loose condition to flow from a hall flowmeter funnel orifice Diameter 0.1 inch/2.5 mm into a specified density cup of definite volume(25 cm³) under controlled conditions.  The mass of powder per unit volume (the ratio between the mass and the volume) is recorded and reported as apparent density. Apparent Density of non-free-flowing powders AS-300 Hall Flowmeter determines the apparent density by permitting a volume or certain quantity of powder in a loose condition to flow from a Car
Post a Comment

Electrolysis process And reduction process information

-
                                                      Electrolysis 

                In this method, an electrolytic cell is set up as shown in figure.  The desired metal is made to act as anode. Anode slowly dissolves and gets deposited on the cathode from where the deposit is removed, washed and dried.


Fig: Electrolysis



                                                           Reduction 

                            Reduction process is carried out in an atmosphere controlled furnace.In reduction process, the compounds of metals usually oxides like iron oxides are reduced with CO/H at temperature below melting point of metal. Tungsten, molybdenum, iron, cobalt, nickel powders are commercially produced by this process.   





Related :-
materials,physical metallurgy, information, materials science,science, mining metallurgy engineering, materials engineering, physical, facebook, journal, mining, metals, chemical, metal, ferrous, category, technology, understand, showing, britannica,electrolysis,
electrolysis of water,
electrolysis hair removal,
faraday's law of electrolysis,
what is electrolysis,
faradays law of electrolysis,
kolbe electrolysis,
electrolysis process,
electrolysis of water class,
faraday law of electrolysisreduction,
clemmensen reduction,
dimensionality reduction,
pdf file size reduction,
reduction meaning,
birch reduction,
pdf size reduction,
size reduction,
belly fat reduction

Comments

Post a Comment

Popular posts from this blog

Atomization process and their types

-
Image
                                                      Atomization Atomization. Atomization, also called the spraying method, is a process in which molten metals are broken into small drops of liquid by high-speed fluids (gas as air or inert gas; liquid as water) or fluids with centrifugal force, and then solidified into powder. There are types of Atomization process are: 1.1 Water Atomization In the commercial production of metal powders water atomization is the pre-eminent mode; attendant capacity worldwide is at least 700000 tyr−1 with production rates up to 500 kg min−1. Water atomization is used primarily for ferrous compositions but can be used to produce a range of nonferrous alloys. It is lower in cost than other modes of atomization but limitations exist in relation to powder purity, particularly with reactive metals and alloys. Nozzles used in water atomization are either in the form of discrete multiple nozzles or an annular slit concentric with the metal stream.
Read more

Machining process information

-
                                                         Machining Introduction :- machining is the most important of the manufacturing processes. Machining can be defined as the process of removing material from a workpiece in the form of chips. The term metal cutting is used when the material is metallic. Most machining has very low set-up cost compared to forming, molding, and casting processes. However, machining is much more expensive for high volumes. Machining is necessary where tight tolerances on dimensions and finishes are required.                  Different Types of Machining Operations :- Three primary machining processes — turning, drilling, and milling — are used as a means of removal. Each process plays a key role in how a product is manufactured and enhances each product’s unique properties... 1) Turning process :-Turning is a machining process performed by a device called a lathe; the lathe spins the given product as the blades cut and scrape away the desired a
Read more

Milling process information

-
Milling Introduction :-Milling is a process performed with a machine in which the cutters rotate to remove the material from the work piece present in the direction of the angle with the tool axis. With the help of the milling machines one can perform many operations and functions starting from small objects to large ones.                         Milling machining is one of the very common manufacturing processes used in machinery shops and industries to manufacture high precision products and parts in different shapes and sizes. types of milling machines 1) Vertical Milling Machines :- The vertical mill has a vertically arranged spindle axis and rotate by staying at the same axis. The spindle can also be extended and performing functions such as drilling and cutting. Vertical mill has got two further categories as well: turret mill and bed mill.                         The turret mill has got a table that moves perpendicularly and parallel to the spindle axis in order to cut th
Read more